Installing a new stereo in your vehicles is a good way to breathe in new life from the old driving days. Adding an MP3 or CD player can give the opportunity to listen to news, music and also improves the overall quality of sound on the cars sound systems. Performing the installation all by yourself is not easy. It requires dedication and patience. Every model of a car is different as well as its stereos. When it comes with car stereo san antonio, individuals can do the installation without any assistance.
To install a new stereo, the old has to be taken out first. To remove it, make sure the vehicle is in parking brake and disconnect the negative cables located in the battery. This must be done first because it will prevent the vehicle from getting short circuit when doing the installs. This will prevent getting harm or lead to fire.
Check and identify for any loose wiring. If the car has no harness or adaptors, they will have to check and identify the wires themselves. Without the adaptor, the connections at the back has to cut. However, when cutting it, do it one at a time to easily remember the color and connection.
If there is no harness, then the wire has must be matched up manually. Every wire is coded by color and will match with the component. However, it is still better to study the diagram to avoid any mistakes. Connect the wiring. Individuals can choose between soldering or crimping. Soldering is able to provide a better and secure connection while crimping is easier and quicker to perform.
After all the connections are done, test out the stereo. However, reconnect first the battery and turn the ignition to ensure it is working fine. Check if the speakers are working properly and the CDS and MP3s play as well. If the antenna of the cable is already connected, then determine if the stereo works.
Loosen the stereo. Every car has a different element in in securing the stereos in its place. If the equipment is being held with nuts or screws, it can be loosened up with a nut driver or screwdriver. If there are no nuts in place, then it needs to be removed with a radio removal key. This type is only limited to other types of vehicles.
Pull out the equipment from its panel. Use a needle nose pliers to easily pull out the component. Simply give it a gentle pull. If the equipment does not budge or hard to pull, then there must be a few nuts that still in place. Double check the wiring and nuts once again.
Before doing the installation, conduct research first. Individuals must learn the right procedure in installing the stereo in its place. There are many factors to consider and the process will differ from one car to another.
Reinstall the trims. Be very gentle and do not break any plastic clips. Install the pieces back at the opposite direction. Install first the last pieces that was removed.
To install a new stereo, the old has to be taken out first. To remove it, make sure the vehicle is in parking brake and disconnect the negative cables located in the battery. This must be done first because it will prevent the vehicle from getting short circuit when doing the installs. This will prevent getting harm or lead to fire.
Check and identify for any loose wiring. If the car has no harness or adaptors, they will have to check and identify the wires themselves. Without the adaptor, the connections at the back has to cut. However, when cutting it, do it one at a time to easily remember the color and connection.
If there is no harness, then the wire has must be matched up manually. Every wire is coded by color and will match with the component. However, it is still better to study the diagram to avoid any mistakes. Connect the wiring. Individuals can choose between soldering or crimping. Soldering is able to provide a better and secure connection while crimping is easier and quicker to perform.
After all the connections are done, test out the stereo. However, reconnect first the battery and turn the ignition to ensure it is working fine. Check if the speakers are working properly and the CDS and MP3s play as well. If the antenna of the cable is already connected, then determine if the stereo works.
Loosen the stereo. Every car has a different element in in securing the stereos in its place. If the equipment is being held with nuts or screws, it can be loosened up with a nut driver or screwdriver. If there are no nuts in place, then it needs to be removed with a radio removal key. This type is only limited to other types of vehicles.
Pull out the equipment from its panel. Use a needle nose pliers to easily pull out the component. Simply give it a gentle pull. If the equipment does not budge or hard to pull, then there must be a few nuts that still in place. Double check the wiring and nuts once again.
Before doing the installation, conduct research first. Individuals must learn the right procedure in installing the stereo in its place. There are many factors to consider and the process will differ from one car to another.
Reinstall the trims. Be very gentle and do not break any plastic clips. Install the pieces back at the opposite direction. Install first the last pieces that was removed.
About the Author:
Get a summary of the factors to consider before selecting an installer of car stereo San Antonio systems and more information about a knowledgeable installer at http://www.baudiosound.com/car-audio-system now.
No comments:
Post a Comment